Alliance-laundry-systems UW35AV Manuel d'utilisateur télécharger pdf (Page 21)

Specifications and Dimensions

F232228

If the existing floor is not reinforced concrete at least

6 inches (153 mm) thick over a solid foundation, cut a

hole approximately 5 feet (1.52 m) square through the

existing floor. Excavate to a depth of 6 inches

(153 mm) from the top of the existing floor. Produce a

pyramid-shaped hole by excavating the bottom of the

hole to a width 6 inches (153 mm) wider on each side

than the width of the top of the hole. Fill with 6 inches

(153 mm) of reinforced concrete. Embed the mounting

bolts or base frame as the concrete is poured. Ensure

that the bolt threads extend 2 inches (51 mm) above

floor level.

After the concrete has cured, proceed as follows:

1. Place the washer-extractor adjacent to the

foundation. Do not attempt to move the machine

by pushing on the sides. Always insert a pry bar

or other device under the bottom frame of the

machine to move it.

2. Remove the wood skid by unscrewing the

carriage bolts holding the skid to the bottom

frame of the washer-extractor.

3. Place the washer-extractor carefully over the

anchor bolts. Never attempt to lift the machine by

the door handle or by pushing on the cover panels.

4. Raise and level the washer-extractor 1/2 inch

(13 mm) off the floor on three points, using

spacers such as nut fasteners.

5. Fill the space between the washer-extractor base

and the floor with a good quality non-shrinking

machinery grout to ensure a stable installation.

Grout completely under all frame members.

(Remove front panel and metal back panel to

gain access to all frame members.) Refer to

Figures 10 through 13. Force grout under

machine base until all voids are filled.

6. Remove the spacers carefully, allowing the

machine to settle into the wet grout.

7. Before grout sets completely, make a drain

opening in the rear of the washer-extractor

grouting with a stiff piece of wire; this opening

should be approximately 1/2 inch (13 mm) wide

to allow any surface water build-up under the

base of the machine to drain away. Do not omit

this step.

8. Position the mounting bolt washers and locknuts

on the anchor bolts and fingertighten locknuts to

machine base.

9. After the grout is completely dry, tighten the

locknuts by even increments – one after the

other – until all are tightened evenly and the

washer-extractor is fastened securely to the floor.

NOTE: Check and retighten the locknuts after five

to ten days of operation and every month thereafter.

10. Check vibration safety switch and gap setting and

switch function.

Figure 10

Figure 11

PHM570N

PHM571N

PHM570N

30.5 in.

(775 mm)

7.3125 in.

(186 mm)

11 in.

(279 mm)

4.0625 in.

(103 mm)

Typical

4.0625 in.

(103 mm)

Typical

30.125 in.

(765 mm)

UW35AV

PHM571N

4.0625 in.

(103 mm)

Typical

4.0625 in.

(103 mm)

Typical

36 in.

(914 mm)

35.625 in.

(905 mm)

9.125 in.

(232 mm)

14.5 in.

(368 mm)

28 in.

(711 mm)

UW60AV

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 33 34

Commentaires sur ces manuels

Pas de commentaire

Alliance-laundry-systems UW35AV Manuel d'utilisateur Page 21

Commentaires sur ces manuels

Produits connexes et manuels pour Rondelles Alliance-laundry-systems UW35AV