Alliance Laundry Systems HCN040HNV Spécifications télécharger pdf (Page 6)

warnings or precautions. To reduce the risk of poisoning or

chemical burns, keep them out of the reach of children at all

times [preferably in a locked cabinet].

• Do not use fabric softeners or products to eliminate static un-

less recommended by the manufacturer of the fabric softener

or product.

• Always follow the fabric care instructions supplied by the tex-

tile manufacturer.

• Loading door MUST BE CLOSED any time the washer is to

fill, tumble or spin. DO NOT bypass the loading door switch

by permitting the washer to operate with the loading door

open. Do not attempt to open the door until the washer has

drained and all moving parts have stopped.

• Be aware that hot water is used to flush the supply dispenser.

Avoid opening the dispenser lid while the machine is running.

• Do not attach anything to the supply dispenser’s nozzles, if

applicable. The air gap must be maintained.

• Do not operate the machine without the water reuse plug or

water reuse system in place, if applicable.

• Be sure water connections have a shut-off valve and that fill

hose connections are tight. CLOSE the shut-off valves at the

end of each wash day.

• Keep washer in good condition. Bumping or dropping the

washer can damage safety features. If this occurs, have wash-

er checked by a qualified service person.

• DANGER: Before inspecting or servicing machine, power

supply must be turned OFF. The servicer needs to wait for at

least 5 minutes after turning the power OFF and needs to

check for residual voltage with a voltage meter. The inverter

capacitor or EMC filter remains charged with high voltage for

some time after powering OFF. This is an imminently hazard-

ous situation that, if not avoided, will cause severe personal

injury or death.

• Do not repair or replace any part of the washer, or attempt any

servicing unless specifically recommended in the user-main-

tenance instructions or in published user-repair instructions

that the user understands and has the skills to carry out. AL-

WAYS disconnect the washer from electrical, power and wa-

ter supplies before attempting any service.

• Disconnect the power by turning off the circuit breaker or by

unplugging the machine. Replace worn power cords.

• Before the washer is removed from service or discarded, re-

move the door to the washing compartment.

• Failure to install, maintain, and/or operate this washer accord-

ing to the manufacturer’s instructions may result in conditions

which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY IN-

STRUCTIONS appearing in this manual are not meant

to cover all possible conditions and situations that may

occur. Common sense, caution and care must be exer-

cised when installing, maintaining, or operating the

washer.

Any problems or conditions not understood should be reported to

the dealer, distributor, service agent or the manufacturer.

WARNING

Machine installations must comply with minimum

specifications and requirements stated in the appli-

cable Installation Manual, any applicable municipal

building codes, water supply requirements, electri-

cal wiring regulations and any other relevant statuto-

ry regulations. Due to varied requirements and appli-

cable local codes, this machine must be installed,

adjusted, and serviced by qualified maintenance per-

sonnel familiar with applicable local codes and the

construction and operation of this type of machi-

nery. They must also be familiar with the potential

hazards involved. Failure to observe this warning

may result in personal injury, property damage,

and/or equipment damage, and will void the warran-

ty.

W820

IMPORTANT: Ensure that the machine is installed on a

level floor of sufficient strength. Ensure that the recom-

mended clearances for inspection and maintenance are

provided. Never allow the inspection and maintenance

space to be blocked.

WARNING

Never touch internal or external steam pipes, con-

nections, or components. These surfaces can be ex-

tremely hot and will cause severe burns. The steam

must be turned off and the pipe, connections, and

components allowed to cool before the pipe can be

touched.

SW014

Safety Decals

Safety decals appear at crucial locations on the machine. Failure

to maintain legible safety decals could result in injury to the oper-

ator or service technician.

Use manufacturer-authorized spare parts to avoid safety hazards.

Operator Safety

Safety Information

1 2 3 4 5 6 7 8 9 10 11 ... 76 77

Commentaires sur ces manuels

Pas de commentaire

Alliance Laundry Systems HCN040HNV Spécifications Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à laver Alliance Laundry Systems HCN040HNV